Reference copy: Rules can change by season or bulletin. Confirm current requirements with USRA and your track before competing.
USRA MODIFIED
Article 8.1 — Wheels
- Must be 15 inches in diameter and 8 inches wide.
- Stickers are not required.
- Reinforced steel only. Added wheel ballast is not allowed. Solid or non-spoked wheels are not allowed.
- A steel or aluminum bead lock may be used on the right-front and right-rear only and may be mounted outside the wheel if it adds no more than 0.75 inch to overall wheel width.
- Homemade mud caps are not allowed.
- Wheel covers are permitted on right-side wheels only; five-fastener type is recommended. Inner mud plugs are permitted. All mud covers must display the car number on at least one side.
- Wide-five wheel adapters are not allowed.
- An aluminum spacer between hub and wheel is permitted, but overall car width cannot exceed 80 inches.
- Aluminum or steel lug nuts are permitted.
Article 8.2 — Tires
- Only the American Racer G60-15 KK704—Short, Tall or X-Tall—is permitted. Tires should durometer 50 or harder after any race. A tire below that reading may be sampled for chemical testing.
- Softening and solvents are not allowed. Tires may not be altered with components or chemicals that change the manufacturer’s baseline settings.
- Grooving and/or siping is permitted.
- All sidewall markings must remain visible. Buffing or removing compound designations is not allowed.
- Adding ballast inside a tire is not allowed.
- Plastic wrap is permitted in the pit stall but must be removed before leaving the stall.
Back to top
USRA STOCK CAR
Article 8.1 — Wheels
- Must be 15 inches in diameter and 8 inches wide.
- Steel lug nuts only.
- Reinforced steel only.
- A steel bead lock may be used on right-side wheels only and may be mounted outside the wheel if it does not add to overall wheel width.
- Homemade mud caps are not allowed.
- Wheel covers are permitted on right-side wheels only. Inner mud plugs are permitted.
- A spacer or adapter, offset wheel, or combination is permitted but must be aluminum and cannot exceed 2 inches total offset per wheel.
- Three tabs no longer than 2 inches each may be welded to the wheel to mount a mud cap.
- Bleeder valves are not allowed.
- Added ballast to any wheel is not allowed.
Article 8.2 — Tires
- Only the American Racer G60-15 KK704—Short, Tall or X-Tall—is permitted. Tires must durometer 50 or harder after a race. A tire below that reading may be sampled for chemical testing.
- Softening and solvents are not allowed. Tires may not be altered with components or chemicals that change the manufacturer’s baseline settings.
- Adding ballast inside a tire is not allowed.
- Grooving and/or siping is permitted.
- Sidewall markings must remain visible. Buffing or removing compound designations is not allowed.
- Plastic wrap is permitted in the pit stall but must be removed before leaving the stall.
Back to top
USRA B-MOD
Article 8.1 — Wheels
- Must be 15 inches in diameter and 8 inches wide.
- Bleeder valves are not allowed.
- Reinforced steel only.
- A steel bead lock may be used on right-side wheels only and may be mounted outside the wheel if it does not add to overall wheel width.
- Homemade mud caps are not allowed.
- Wheel covers are permitted on right-side wheels only. Inner mud plugs are permitted.
- Wide-five wheel adapters are not allowed. Steel lug nuts only.
- An aluminum spacer between hub and wheel is permitted, but overall racecar width cannot exceed 78 inches when measured from the top of the left tire to the bottom of the right tire at the widest point.
- Added ballast to any wheel is not allowed.
- Solid or non-spoked wheels are not allowed.
Article 8.2 — Tires
- Only the American Racer G60-15 KK704—Short, Tall or X-Tall—is permitted. Tires must durometer 50 or harder after a race. A tire below that reading may be sampled for chemical testing.
- Softening and solvents are not allowed. Tires may not be altered with components or chemicals that change the manufacturer’s baseline settings.
- Grooving and/or siping is permitted.
- Sidewall markings must remain visible. Buffing or removing compound designations is not allowed.
- Adding ballast inside a tire is not allowed.
- Plastic wrap is permitted in the pit stall but must be removed before leaving the stall.
Back to top
USRA TIRE TESTING
Article 8.3 — Applies to the classes above
- Random gas-chromatography scans may be performed to identify illegal substances. A GC scan should peak at 19–20 minutes. If there is no peak, the driver will be disqualified. The driver may protest and request a mass-spectrometry test at the driver’s cost, usually around $300. The mass-spec test identifies the substance used. The main tire peak should never be split in half.
- Traces or excessive quantities of chemicals outside the baseline result in automatic disqualification. A first offense results in loss of all season points, forfeiture of event prize money, a fine up to $5,000 and an indefinite suspension from USRA events. The driver cannot compete in future USRA events until the fine is paid in full.
- USRA strongly recommends using only soap and water. Baking tires will not eliminate traces of illegal substances. USRA will aggressively test for illegal substances and levy severe punishment for infractions.
Back to top